Ion^® JSPII

Sump & Battery Backup System

1/3 HP stainless steel/cast iron as an everyday primary sump pump with a battery-operated secondary pump for automatic backup during power outages.

Comes fully assembled with pumps and valves pre-plumbed. Simply drops into sump pit for easy installation.

The Ion Switch controls primary pump without moving parts or contact points. Runs on utility power with a pumping capacity rated at 43 GPM (at 10' of head).

Uses one 12-volt Power+ AGM maintenance free battery (purchased separately) to run backup pump when utility power becomes unavailable.

High output 8-amp charger unit with five stages. Built-in audible alarm and indicator lights for easy identifying of system status.

Ion 30ACi Power Pac Battery Backup/Auxiliary AC Alternating Sump Pump System

Ion 30ACi Deluxe Dual Source AC Battery Backup System Components

Installation Components

Included with System

Ion Genesis
Power inverter/battery charger
Battery box
Ion WC33i Sump Pumps
Control Sensors
(configured with Ion Genesis)

Additional Notes

Also included are battery leads and two pipe mount brackets
One 12-volt Power+ AGM battery required
(sold separately via Ion Technologies supplier)
Sump pit not included

Ion WC33i

Two Equivalent High-Capacity Sump Pumps

Integrates with our fully automatic dual source AC auxiliary power supply for everyday primary and emergency backup functionality. Its high rated pumping capacity of 43 GPM at 10-foot total dynamic head is equipped to keep up with continuous or high water flows in residential or light commercial applications when used as a primary or backup.
Consumes power from house electric when available during normal day-to-day use. Alternates cycles between both pumps to balance workload and to prolong system life by avoiding extended wear or idleness to either pump. Two-pump redundancy backup offers emergency coverage in the rare event of a mechanical failure to either pump.
When house electric becomes unavailable, the heavy duty power inverter produces 120-volt standard AC electricity from converted DC battery to operate either pump as a fully powered backup. Maintains high pumping capacity through full duration of use for steady, high performance backup that equals its day-to-day primary functionality.
Built with heavy-duty cast iron for withstanding excessive, high demand use. Minimizes general wear and tear to prolong pump life.

Power Outages
Mechanical Failures

Converts DC Battery Power to Standard AC Electricity

dual-source-ac-backup-sump-pump-powering-from-converted-battery-05

Immediately detects when house electric becomes unavailable. Heavy-duty power inverter automatically converts DC battery power from one 12-volt Power+ AGM (sold separately) to 120-volt standard AC electricity to fully run the system pump.
Maintains its high rated pumping capacity through from onset through full duration of use to push out water and keep the basement dry during power outages. Sustains full performance until battery is completely depleted.
Low amp pump draw consumes half the power of conventional pumps to save battery and extend runtime. Power+ AGM’s 100 amp draw capacity offers nearly twice the amount of power of typical marine batteries.
Power inverter’s built-in charger powers battery back to 100 percent once house electric returns. Stays fully charged for when the next outage occurs.

Runs off House Electricity, Avoids Unnecessary Battery Use

dual-source-ac-backup-sump-pump-powering-from-house-utility-05

Activates the system pump once water in the sump pit reaches a specific level, presumingly as a result of a mechanical failure to an existing primary sump pump.
Runs off house electric, completely bypassing the battery and avoiding unnecessary use as long as utility power remains available.
Continues running as needed while maintaining its high rated pumping capacity. Leaves reasonably ample time for servicing or replacing of the inoperable primary.
Consumes battery only when house electric becomes unavailable. Ensures battery stays at 100 percent and fully charged for backup use when the next outage occurs.

Equipped with the Ion+ Digital Level Control & High Water Alarm

Eliminates Common Mechanical Pump Failure

Solid-state pump control pioneered by Ion Technologies. Proprietary digital float sensor detects water levels to electronically turn system pump on/off with zero moving parts to wear or fail, virtually eliminating common pump failures.
Removes up to 6-inches of water per cycle, one-third times more than with traditional pump switches. Reduces number of cycles to lessen pump activations over time and prolong pump life.
Integrated alarms notify via LED indicators and audible buzzer when water continues to rise. Allows opportunity for response to an arising problem.
Optional upgrade to the Ion Genesis smart controller with programmable level adjustments and additional system monitoring.

Ion+ Digital Level Sump & Sewage Pump Controller

Pump Performance

Ion Technologies WC33i

System Performance

Ion Technologies 30ACi Deluxe

Literature

30ACi+ Sales Brochure

30ACi+ Operation Manual

Legacy

30ACi Operation Manual

Need Additional Assistance?

We are here to help with product selection, technical support, accessory replacing, or general customer service. To get in touch with an Ion Technologies in-house support team member, you may send us a message or call us at our Metropolitan Industries headquarters at 815-372-2493.

Where to Buy

Find Installer